sanitize 7833R
Does anyone know of an approved method of sanitizing a PXI-7833R? We need to remove any proprietary information from the board so thatit can be removed from a secure lab. Thanks.
View ArticleUsing PXI-6682(H) in PXI Express chassis to replace backplane clock
I have a PXI-6682H in a PXIe-1075 which I use for event timestamping. I also have a PXIe-6672 card in the timing slot. I would like to replace the 10 MHz backplane clock to use the 6682 as a GPS...
View ArticlePXI or CRIO differential analog output modules
Does NI have any differential analog output boards or do you just have to use two channels to create the differential signal?
View ArticleErreur accès cible RT en FTP
Bonjour,Je sollicite votre aide pour un problème qui survient sur un banc de test, dont l’architecture est la suivante : Rack de testContrôleur NI PXI-8186 (il me semble) et diverses cartes...
View ArticleProblem to import a file from a real-time target through FTP
Good morning, I need your help for an error on a test bench, which has the following architecture: Test rackNI PXI-8186 controller (I think) and I/O cardsWindows 2000Execution of test sequences with...
View ArticlePXI 5105 on board memory option - how to check what version it is ?
Hi I have recently purchased a second hand NI PXI-5105. I know this model comes with three diffrent on board memory options: 16,128 and 512. I haven't found any option indicator on the board itself....
View ArticleNI Max "loses" instruments when test is uninstalled which forces a reboot...
I am trying to find root cause of an issue where I can load my app and execute it multiple times without issue. When I close my app, sometimes NI max no longer lists any instruments. This causes a...
View ArticleDo NI have a PXIe Fibre Optic Power Meter to measure loss (attenuation) and...
Hi, I want to be able to measure the loss in a Fibre Optic cable at a wavelength of 650nm, is there any PXIe cards that can perform this functionThanks
View ArticleHow to join a network domain with the rt controller running PharLab?
I have a PXI system that I would like to be able to access throughout the corporate network. Currently, I am accessing it via the IP address, but would like to use the Host Name instead. Unfortunately,...
View ArticlePXI-7854R I/O pin state when bitfile is reloaded
PXI-7854R has Virtex5 FPGA. I use some of the FPGA pins as digital output pins, either set to high or low states. If I load another bitfile (either the same or different) then what is the expected...
View Articlehow to use 9871 RS485 card in scan mode in PXI-7813R (Reconfigurable IO)
I would like to use 9871 in scan mode in RT code rather than writing FPGA code.Plese find the attached snapshot of RT project.
View Articlenihsdio.dll not found
Hi, I have recently installed LabVIEW 2013, up from 2011, and now a Get Session Reference VI cannot get the session reference. The session reference is still there but the connecting wire is broken.I...
View ArticleSeeking help for PXI card Installation Procedure Guidance
I have PXI-1042 Chassis with PXI Card numbers 2503 MUX , DIO and AIO cards. We are running LabWindows CVI with TestStand 3.0.I have to load all of the above into a new system. I wanna know the step...
View ArticleDriver NI PXIe 5641r for Labview 2012
hi. i have module NI PXIe 5641r and labview 2012, i installed driver NI PXIe 5641r; however this driver did not support labview 2012 softwave. help me please!
View ArticleClik here to view.
PXI-6682H
Hello. I have PXI-6682H with chasis PXIe1082. I'd like to set time of my timing module from NTP server and get time with resolution of 1 usec. Also i would like to synchronize my ni5761 module and get...
View ArticleRead data from FlexRIO
Hello.I have a timing diagram (see. Fig. below). It is necessary to read the data coming from the chip (signal D * x). I use the PXIe-7962 and NI 6587 (Serdes Connector CLIP Reference). At the signal...
View ArticleUsing NI PXI-2520 and DMM to perform Electrical test for electronic module (BUT)
Hello, I’m new in PXI technologies, and I want to learn how to perform some basic test for electronics modul (UUT),to began I have read some manual explaining the architectur of switching card also the...
View Article1085 expansion
Expanding a 1085 chassis using an 8374, do I need a 6683h and 6674T in the slave chassis or only in the master, the controller is an 8135.
View Articlepxi
Hi everybody, I have a problem: I cannot acquire 6 analog signals with a PXIe 8135 with 4MS/s. I use two boards with 4 MS/s, 16 bits and 8 Analog Inputs. I use a subVI of SAMPLE CLOCK for configuration...
View ArticlePXI 1010 chassis controller options
I have a PXI 1010 chassis and am wondering if my MXI-Express PXI 8360 controller is compatable with it. I have not been able to find anything in the forums about controller options. kph
View Article