SCXI 1314 Proper Wiring
Hello, We have a three wire strain gage (red, white, black) and we are trying to connect it to the SCXI-1314 module. I was hoping somebody could say the proper way to do so. Thanks
View ArticleNI PXI with NI 2527 for test a relay
Hello,I have a test system with NI-PXI , NI DMM SWITCH 2575 for connection test on a fusebox and NI 2527 for POWER SWITCH for relais test.From time to time, there are parts which fail at a relay test...
View ArticleBluetooth Analysis Interactive Example: won't connect to PXIe-5644R
The data sheet for the Analysis Toolkit indicates compatibility, but the canned example won't connect to the module. I need this to evaluate the system, and I won't have the eval long enough to write a...
View Articlepci 8330 not detected
Hi all.I have a PCI-8330 card and it is installed in an old computer with a VIA processor 1GHz, 1Gb Ram and with Win2KSP4I have installed previously the MXI-3 software version 1.15.When I run the MXI-3...
View ArticleSMU Guarding
Hi All, I'm looking to perform some low current measurements on my DUT and therefore am looking at including the Guard wires on my DUT evaluation PCB. I have two related questions on this issue. 1: The...
View ArticleMXI-express Panel Mount Feed Through Connector
Does NI sell such a product? I want to feed the MXIe from my PXIe unit, through a panel I will make, in the front of a 19" rack. I need that feed through connector, one that can be mounted on a panel,...
View ArticleClik here to view.
pll was unlocked 200007
We are going to use the laboratory complex of Modern wireless networks, which contains of PXI-1075e, Vector Signal Generator NI PXIe-5673E and Vector Signal Analyzer NI PXIe-5663E, for teaching...
View Articlepxi
Hi I am using NI 5791 tranceiver equipped with PXIe-7966R FPGA.My question is that can I use this tranceiver card in full duplex mode.That menas I can use transmit and receive channels at the same time...
View ArticleClik here to view.
DCPower SFP monitor
Good day, i would like to use SFP (soft front panel) of our DCPower PXI4110 inserted into PXIe 1078 chassis with PCIe connected to external PC to monitor the orange led of ch2.Apparantly, i get no...
View ArticlePXI-6221 and PXI-2566 not recognized in MAX
Configuring RT PXI system: 1050 chassis, 8108 controller in slot 1, slot 2 empty, 6221 AI cards in slots 3&4, 6733 AO cards in slots 5&6, 6529 DIO card in slot 7 and 2566 Relay card in slot 8....
View ArticleSynchronize PXI FPGA 7841 with 4140 Source Meter with trigger
Hi, I work with a PXI system including a FPGA 7841 and a 4140 Source Meter Unit. The SMU is used to supply a sensor (DC voltage 3.3V) and I implemented an i2c protocol on the FPGA board to communicate...
View ArticlePXIe-1073 link LED off and chassis not seen by computer
Yesterday, the PXIe-1073 was able to connect to our computer just fine and appeared in NI MAX. However, after installing some updates and rebooting the computer, the PXIe-1073 no longer shows up in NI...
View ArticlePXI 8430 cannot open serial ports
Hi all,I have problems using serial ports of the PXI-8430/8 card.After driver setup the device works pretty well and the serial Troubleshooter of MAX shows all 8 ports as passed and I can access the...
View ArticleImproving digitizer accuracy via oversampling
This question is generally for any signal and digitizer but in particular we have a PXI-5105 and are wondering if there is any statistical basis for impriving absolute accuracy via oversampling? We...
View ArticleHow to generate Digital Pulse using PXI-6238
Dear All I want to produce Digital pulse from PXI-6238 or PXI-6704 or PXI-6527 ( i have all these) with DAQmx 8.7.1 in LabVIEW 7.1. when i configure a channel in any of the above...
View ArticleCompile EXE of VI to run on PXI
I've got a VI that needs to run on the RT PXI, using Labview 2014.This VI has a front end where the user changes values etc, so it must be visible on the desktop PC, connector to the PXI via ethernet....
View ArticleNI Max simulated PXI device not present in Labview project
I've added a simulated NI-PXI-6527 digital IO card to my PXI in NI MAX, but it does not seem possible to access this simulated IO card in a Labview project.Is this normal ?
View ArticlePXI
Hello, I would like to use an NI PXIe-5644 Vector Signal Transceiver in a Keysight M9018a PXIe chassis with Keysight M9036a controller. Has anyone done this? Will I be able to setup the NI VST?...
View ArticlePXIe 5170R FPGA decimation options and continuous acquisition
Can PXIe-5170R be configured arbitrary decimation options and Continuous acquisition(I mean that acquisition data several minutes only oneshot but not in while loop acquisition series data and wait the...
View ArticleHere are the NI part numbers of cabling information that I need (i: drawings,
Here are the NI part numbers of cabling information that I need (ie: drawings, data sheets etc)SH100100776990-01185095-02192061-02192061-01782271-01I'm looking for a product drawing that would show...
View Article